USS Intrepid - Part 2

Published: October 1st, 2014     
Product Image
Box art
Reviewed by: Bill Kluge - IPMS# 45849
Scale: 1/350
Company: Gallery Models
Price: $329.98
Product / Stock #: 64008
Product provided by: MRC

The Ship

Launched in April 1943 and commissioned four months later, USS Intrepid (CV-11) participated in numerous actions in the central and western Pacific from early 1944 until the end of the Pacific War, including Leyte Gulf and Okinawa. She was hit twice by kamikazes but was still on station at the end of hostilities. Intrepid underwent modernization twice during the 1950s, which enclosed her bow and gave her an angled flight deck. Reclassified as an Anti-submarine Carrier (CVS-11), Intrepid was the lead ship for the NASA's Mercury Aurora 7 and the Gemini 3 splashdown recovery. From April 1966 to February 1969, she made three deployments to the waters off Vietnam. She ended her active career back in the Atlantic and Mediterranean, being decommissioned in 1974 with over 30 years of service. In August 1982, Intrepid was reopened as a museum ship in New York harbor.

The Model: Part 2 - Construction Begins

On full hull ship models, for me the build begins by cutting the hull for a waterline display. With this kit, I would use a different technique to model water. I stripped one side of the paper off of a piece of 3/16-inch foam core board, exposing the Styrofoam middle. The remaining paper side was glued to a thin plywood board to form the base. I would use the thickness of the foam, carved and sanded to shape, to replicate waves and troughs. This meant that I needed to measure down from the top of waterline to accommodate the thickness of the foam.

As mentioned earlier, the waterline is nowhere indicated on the hull. Studying photos of the real hull and comparing to the kit, I determined the point of the top edge of the boot top. Using Chartpak tape to approximate the foam thickness, I made the cut using a Dremel cutting wheel. The plastic of the hull is very thick, nearly twice as thick as what I'm used to, so it was a slow, messy process. On the other hand, the thickness adds rigidity. I glued in a couple of pieces of scrap plastic to act as anchoring strips, and with the hanger deck in place, no additional hull bracing was needed. The hull was test fitted to the base board, the foam was cut out to fit the hull, and the board and anchoring strips were drilled to accommodate holding screws. I'll work on the water later on.

Early on, I had decided to build this kit as USS Hancock. Only a few alterations are required to modify the kit, and the first change to make is altering the bow anchor hawses. I chose to remove Intrepid's stem hawsehole by sanding off the protruding lip and filling the indent in the bow with Magic Sculp. The bow is molded with additional hawseholes on both sides, so once the "unused" side is drilled out, anchors can be placed on both sides of the bow.

The two-piece hanger deck fits easily into place. Twelve bulkhead pieces build the sides up to the flight deck level. Sponsons are then added to support the flight deck. The way these bulkheads are designed would seem to allow relatively easy parts changes to reconfigure as other ships of the class. At this point, knowing that some aircraft would be placed on the hanger deck, ship construction was suspended in favor of the aircraft.

Eighteen aircraft come with the kit. I'll use all but two of the helicopters, and I added three Trumpeter A3 Skywarriors. Each of these aircraft is a small kit by themselves, with anywhere from a dozen to twenty parts. Many of the parts are quite small or very thin and delicate, so extreme care is needed when handling them. I had crushed a Skyhawk's tail, and launched a Crusader main gear into the unknown before I knew it.

All the kit's aircraft come with wings unfolded, but in reality unless they're about to launch, aircraft are almost always seen on board with their wings folded. I planned on having one E-1 Tracer on the cat about to launch, so all the other aircraft (except the A4s) would have their wings cut and folded. That will make the deck look more empty, but I'm counting on Gallery releasing more aircraft in the future, and I plan on bringing the squadrons up to full strength eventually. Also, Skyhawks were almost always seen with their drop tanks attached, so I set about replicating drop tanks from cut pieces of sprue trees, carved and sanded to shape. Pylons were made from small Evergreen strips. A couple of completed aircraft will be glued to the hanger deck where they can be seen, and construction on the ship will recommence.

Thanks to MRC and IPMS/USA for the opportunity to build and review this kit.

  • Hull cut
    Hull cut
  • Hangar deck
    Hangar deck
  • Bow mod
    Bow mod
  • Skyraider
    Skyraider
  • Skyraider
    Skyraider
  • Skyhawk
    Skyhawk
  • Pylons
    Pylons
  • Skyhawk
    Skyhawk
  • Droptanks
    Droptanks
  • Crusader
    Crusader
  • Crusader
    Crusader

Post new comment

The content of this field is kept private and will not be shown publicly.
  • Web page addresses and e-mail addresses turn into links automatically.
  • Allowed HTML tags: <a> <blockquote> <br> <cite> <code> <dd> <div> <dl> <dt> <em> <li> <ol> <p> <span> <strong> <ul>
  • Lines and paragraphs break automatically.
  • Allowed HTML tags: <a> <em> <strong> <cite> <code> <ul> <ol> <li> <dl> <dt> <dd>
  • Non-latin text (e.g., å, ö, 漢) will be converted to US-ASCII equivalents (a, o, ?).

More information about formatting options

CAPTCHA
This question is for testing whether you are a human visitor and to prevent automated spam submissions.